How do I calculate the weight of stainless steel?
Weight = Cross-Sectional Area × Length × Density. Compute the cross-sectional area of the shape (π × d²/4 for round bar; π × wall × (OD − wall) for pipe; width × thickness for flat bar and plate), multiply by length in metres and by the grade density in g/cm³ (7.93 for 304/304L, 7.98 for 316/316L), then divide by 1000 to get kg. For sheets where width, length and thickness are all in mm, divide by 1,000,000 instead.
Is the calculated weight the same as the actual weight?
No. Calculated weight is theoretical weight based on nominal dimensions and nominal density. Actual weight differs because of rolling tolerances (±5–10% on thickness/diameter/wall), heat-to-heat composition variation, surface-finish material removal (pickling, polishing), and pipe wall-tolerance practices. Most mills invoice on theoretical weight; always confirm the weight basis with your supplier.
What is the density of 304 stainless steel?
304/304L stainless steel has a density of 7.93 g/cm³ (7930 kg/m³, 0.286 lb/in³). The same value applies to the wider 300-series family - 201, 202, 301, 302, 303 and 321 - while 316/316L is slightly heavier at 7.98 g/cm³.
What is the density of 316 stainless steel?
316/316L stainless steel has a density of 7.98 g/cm³ (7980 kg/m³, 0.288 lb/in³). The extra molybdenum (2–3%) that gives 316 its superior pitting resistance also makes it about 0.6% heavier than 304.
How do I calculate the weight of a stainless steel pipe or tube?
Use: Weight (kg/m) = π × wall × (OD − wall) × ρ ÷ 1000 - OD and wall in mm, ρ in g/cm³. A 304 pipe, OD 21.3 × 2.77 mm, therefore weighs 3.14159 × 2.77 × 18.53 × 7.93 ÷ 1000 ≈ 1.28 kg/m. This works for both seamless and welded pipe, round tube, and pressure tube.
How much does a 4×8 sheet of 304 stainless steel weigh?
A 4 ft × 8 ft (1219 × 2438 mm) 304 sheet weighs 23.6 kg (52.0 lb) per 1 mm of thickness. Common values: 2 mm → 47.2 kg (104 lb), 3 mm → 70.7 kg (156 lb), 6 mm → 141.5 kg (312 lb), ½″ (12.7 mm) → 299 kg (660 lb). For 316, multiply by 1.006.
| Grade / UNS | Family | Density g/cm³ | Density kg/m³ | Density lb/in³ |
|---|---|---|---|---|
| 201, 202 (S20100, S20200) | Austenitic | 7.93 | 7930 | 0.286 |
| 301, 302, 303 (S30100, S30200, S30300) | Austenitic | 7.93 | 7930 | 0.286 |
| 304, 304L, 304H (S30400, S30403, S30409) | Austenitic | 7.93 | 7930 | 0.286 |
| 305 (S30500) | Austenitic | 8.00 | 8000 | 0.289 |
| 309, 309S (S30900, S30908) | Austenitic | 7.98 | 7980 | 0.288 |
| 310, 310S (S31000, S31008) | Austenitic | 7.98 | 7980 | 0.288 |
| 316, 316L, 316H (S31600, S31603, S31609) | Austenitic | 7.98 | 7980 | 0.288 |
| 316Ti (S31635) | Austenitic | 8.00 | 8000 | 0.289 |
| 317, 317L (S31700, S31703) | Austenitic | 8.00 | 8000 | 0.289 |
| 321 (S32100) | Austenitic | 7.93 | 7930 | 0.286 |
| 347 (S34700) | Austenitic | 8.00 | 8000 | 0.289 |
| 904L (N08904) | Super austenitic | 7.95 | 7950 | 0.287 |
| 409 (S40900) | Ferritic | 7.70 | 7700 | 0.278 |
| 410 (S41000) | Martensitic | 7.70 | 7700 | 0.278 |
| 420 (S42000) | Martensitic | 7.70 | 7700 | 0.278 |
| 430 (S43000) | Ferritic | 7.70 | 7700 | 0.278 |
| 434, 439 (S43400, S43035) | Ferritic | 7.70 | 7700 | 0.278 |
| 440A / 440B / 440C (S44002–04) | Martensitic | 7.70 | 7700 | 0.278 |
| 446 (S44600) | Ferritic | 7.50 | 7500 | 0.271 |
| 2205 Duplex (S32205 / S31803) | Duplex | 7.80 | 7800 | 0.282 |
| 2507 Super Duplex (S32750) | Super duplex | 7.80 | 7800 | 0.282 |
| 17-4PH (S17400) | Precipitation-hardening | 7.80 | 7800 | 0.282 |
| 15-5PH (S15500) | Precipitation-hardening | 7.80 | 7800 | 0.282 |
To calculate the weight of stainless steel (plates, pipes, or round bars) based on your specific dimensions and units (inches or millimeters), click the button below to perform the calculation.






