254 SMO Stainless Steel: Super Austenitic Grade for Seawater and Chloride Service
Aug 01, 2025
Leave a message
Why 254 SMO Is Classed as a Super Austenitic Grade
254 SMO (UNS S31254, EN 1.4547) is a super austenitic stainless steel built for seawater and high-chloride service. It is a fully austenitic grade, so it keeps the ductility and fabrication behaviour of the 300 series, yet its alloy content lifts pitting resistance far beyond 316L and even past 904L. The grade is supplied under ASTM A240 for plate and sheet, ASTM A182 F44 for forgings, ASTM A312 for pipe, and ASTM A789 and ASTM A790 for tubing and welded pipe.
Designers turn to this grade when chlorides, temperature, and residual stress combine to rule out conventional stainless steels, and when a nickel alloy would be over-specified or difficult to obtain.
Chemical Composition and PRE
Pitting resistance equivalent is calculated as PRE = %Cr + 3.3 x %Mo + 16 x %N, and the high molybdenum and nitrogen levels of this grade are what set it apart.
| Element | Typical range |
|---|---|
| Chromium | 19.5-20.5 % |
| Nickel | 17.5-18.5 % |
| Molybdenum | 6.0-6.5 % |
| Nitrogen | 0.18-0.22 % |
| Carbon | max 0.020 % |
| Pitting resistance equivalent | about 43 |
For comparison, 316L sits near a PRE of 26 and 904L near 33, so this grade occupies a clear step above both. Copper is also added at around 0.5-1.0 % to improve performance in sulphuric acid service.
Performance in Seawater and Chloride Service
The combination of chromium, molybdenum, and nitrogen gives strong resistance to pitting, crevice corrosion, and chloride stress corrosion cracking. The grade is routinely selected for permanent contact with seawater, including splash-zone fittings on offshore structures, where a 316L component would suffer crevice attack within a short service period.
High resistance to pitting in neutral chloride solutions.
Effective barrier against crevice corrosion under gaskets and deposits.
Greater tolerance of chloride stress corrosion cracking than 316L.
Good resistance to sulphuric acid and many reducing acid media.
Because chloride performance is the deciding property, purchasers normally require corrosion testing to ASTM G48 Method A or Method B on each heat to confirm the delivered material meets the specified critical pitting or crevice temperature.
Mechanical Properties and Fabricability
Tensile strength falls in the range of 650-800 MPa with yield strength of at least 300 MPa, and elongation reaches about 40 %, so the grade tolerates cold forming well. It work-hardens faster than 316L, which means cold forming or drawing sequences need intermediate annealing to avoid cracking.
Welding uses standard GTAW and GMAW methods with a matching high-molybdenum filler. No post-weld heat treatment is required, but heat input and interpass temperature must be controlled, and the finished weld should be cleaned free of oxide, since embedded iron or scale can become an initiation site in seawater.
How It Compares with 904L
Both grades are molybdenum-rich austenitic stainless steels, but they are aimed at different environments. 904L performs well in sulphuric and phosphoric acid service and in mixed acid environments, while this grade is stronger in neutral chloride solutions such as seawater. It also delivers higher strength than 904L, which can allow thinner components in pumps, valves, and heat exchanger parts.
Typical Applications
Seawater cooling and fire-fighting systems.
Desalination plant pumps, valves, and piping.
Offshore oil and gas equipment exposed to chlorides.
Flue gas desulphurisation scrubber components.
Pulp and paper equipment handling aggressive process fluids.
Heat exchangers using brackish or saline cooling water.
Frequently Asked Questions
Q: What does the name 254 SMO stand for?
The designation is a commercial grade name, and the material is standardised as UNS S31254 or EN 1.4547.
Q: Is 254 SMO magnetic?
It is fully austenitic and therefore essentially non-magnetic in the annealed condition, similar to 316L.
Q: Can it replace 316L in seawater pipes?
Yes, in most seawater duties it is a direct upgrade, offering far longer service life than 316L at lower cost than a nickel alloy.
Q: Does it resist chloride stress corrosion cracking?
It resists it far better than 316L, though it is not immune, and highly stressed components in hot concentrated chlorides should still be verified by testing.
Q: What filler metal is used for welding?
A matching high-molybdenum austenitic filler is used, and the welding procedure must be qualified for the joint and thickness involved.
Q: Is post-weld heat treatment required?
No. Solution annealing is only needed when cold work or poor welding practice has damaged the corrosion resistance of the surface.
Send Inquiry






