AISI 316 4x8 Feet Stainless Steel Plate: Specifications and Buying Guide

Jul 11, 2025

Leave a message

What Does a 4x8 Feet Stainless Steel Plate Mean

A 4x8 feet stainless steel plate measures 4 feet by 8 feet, which equals 1219 mm by 2438 mm in metric units. This is the most widely stocked format for stainless steel sheet and plate worldwide, because it fits standard processing equipment and shipping containers. AISI 316 in this format is used for chemical equipment, food machinery, marine trim, heat exchangers, and architectural panels where molybdenum-bearing corrosion resistance is required.

Grade Designations and Chemical Composition per ASTM A240

Type 316 corresponds to UNS S31600, EN 1.4401 with the designation X5CrNiMo17-12-2, and JIS SUS316. Flat products are normally supplied to ASTM A240 / ASME SA240, EN 10088-4, or JIS G4304. The 2.0-3.0% molybdenum content is the key difference from type 304: it improves resistance to pitting and crevice corrosion in chloride and acidic environments.

Element Content (%)
Chromium (Cr) 16.0 - 18.0
Nickel (Ni) 10.0 - 14.0
Molybdenum (Mo) 2.0 - 3.0
Carbon (C) 0.08 max
Manganese (Mn) 2.00 max
Silicon (Si) 0.75 max
Phosphorus (P) 0.045 max
Sulfur (S) 0.030 max
Nitrogen (N) 0.10 max

Mechanical Properties and Standard Thicknesses

Minimum mechanical properties per ASTM A240 for UNS S31600 are tensile strength 515 MPa, yield strength 205 MPa, and elongation 40% in 2 in. Standard thicknesses for 4x8 plates run from 1.5 mm to 50 mm, with the most common stock at 2 mm, 3 mm, 5 mm, 6 mm, 8 mm, 10 mm, and 12 mm. The thickness tolerance becomes looser as the plate gets thicker, typically from about plus or minus 0.03 mm on thin sheet up to about plus or minus 0.75 mm on heavy plate, while the width and length tolerance on a standard 4x8 plate is about plus or minus 2 mm. The exact tolerance table is stated in the applicable standard such as ASTM A240 or EN 10029 and is confirmed by the mill test certificate.

Surface Finishes for 4x8 Plates

Common finishes are 2B, which is cold rolled and bright with a smooth surface and is the standard for general fabrication; No.1, which is hot rolled and annealed with a matte surface and is used where appearance is not critical; BA, which is bright annealed with a mirror-like base for decorative work; No.4, which is brushed for food machinery and architectural trim; and 8K, which is mirror polished for decorative panels. The finish affects price, reflectivity, and cleanability, but it does not change the corrosion resistance of the base material.

Plate Weight Calculation

The weight of a plate is length x width x thickness x density, with the density of 316 taken as 7.98 g/cm³. A 1219 x 2438 mm plate has an area of 2.97 m², so the weight scales directly with thickness. The table below gives approximate weights for common thicknesses.

Thickness (mm) Approximate weight of 1219 x 2438 mm plate (kg)
3 71
5 118
6 142
10 237
12 284

These figures help plan lifting equipment and freight. The weight stated on the mill test certificate is the reference for invoicing.

FAQ

Q1: Is AISI 316 the same as EN 1.4401?
A: Yes, EN 1.4401 with the designation X5CrNiMo17-12-2 is the European designation for the same grade as AISI 316 and UNS S31600.

Q2: What is the difference between 316 and 316L?
A: 316L, which is UNS S31603 and EN 1.4404, limits carbon to 0.03% max, which reduces chromium carbide precipitation during welding and improves intergranular corrosion resistance; 316 is preferred where maximum high-temperature strength is needed.

Q3: What thickness tolerances apply to 4x8 plates?
A: The tolerance depends on the standard and the nominal thickness and width, typically about plus or minus 0.03 mm for thin sheet up to about plus or minus 0.75 mm for thick plate; the exact range is stated in the mill test certificate per ASTM A240 or EN 10029.

Q4: Which finish should I choose for food processing equipment?
A: A No.4 brushed finish is common because it is smooth, easy to clean, and hides fingerprints; 2B is acceptable where the surface will be painted or covered.

Q5: Can 316 plate be laser cut and bent?
A: Yes, 316 has good formability. Use laser, plasma, or waterjet cutting, and account for the slightly higher work-hardening rate of 316 compared with 304 when planning bending operations.

Q6: How do I calculate the weight of a 4x8 316 plate?
A: Multiply the area of 2.97 m² by the thickness in meters and by the density of 7.98 g/cm³; a 3 mm plate weighs about 71 kg.

Send Inquiry