2205 Duplex Stainless Steel: Strength and Corrosion Resistance Explained

Jul 28, 2025

Leave a message

What Is 2205 Duplex Stainless Steel?

2205 is the most widely used duplex stainless steel. Its microstructure consists of roughly equal proportions of austenite and ferrite, a balance that gives the grade about twice the yield strength of conventional austenitic stainless steels while retaining much of their toughness and corrosion resistance. The name comes from the classic 22 % chromium, 5 % nickel formulation, and the grade is supplied under UNS S32205, with the earlier UNS S31803 designation still appearing on older drawings. Because strength and corrosion resistance are both available in one material, designers frequently use 2205 to reduce wall thickness, cut weight and extend service life in chloride-bearing installations.

Chemical Composition and Governing Standards

The chemistry is carefully balanced so that the two phases remain in equilibrium after solution annealing and welding.

Element Composition, wt % Role
C 0.030 max Limits carbide precipitation
Mn 2.00 max Residual control
Si 1.00 max Deoxidation
P 0.030 max Residual control
S 0.020 max Residual control
Cr 21.0-23.0 Passive film, pitting resistance
Ni 4.5-6.5 Austenite former
Mo 2.5-3.5 Pitting and crevice resistance
N 0.08-0.20 Strength, austenite balance, pitting resistance
Fe Balance Matrix

UNS S32205 narrows the molybdenum range to 3.0-3.5 % and the nitrogen range to 0.14-0.20 %, which lifts the pitting resistance equivalent number to roughly 34-36 compared with about 34 for the looser S31803 specification. Product standards in common use are ASTM A240 for plate, sheet and strip, ASTM A276 for bars, ASTM A789 and ASTM A790 for tubing and pipe, ASTM A928 for welded pipe, and ASTM A182 for forgings. The European designation is 1.4462, written X2CrNiMoN22-5-3.

Strength and Mechanical Properties

The duplex structure is the source of the grade's main commercial advantage. Minimum room-temperature values for annealed product are shown below.

Property Minimum requirement Comment
0.2 % yield strength 450 MPa About twice that of Type 304 or 316
Tensile strength 620 MPa Typical annealed values run higher
Elongation 25 % Good ductility for forming
Hardness About 290 HBW maximum Cap protects toughness and stress corrosion performance
Impact toughness Specified for thick sections Charpy testing is normal for heavy-wall and low-temperature service

Because the allowable stress is high, a 2205 vessel or pipeline can often be built with a thinner wall than the equivalent 304 or 316L design. That reduction in section and weight is usually the reason the grade is selected, and it should be calculated against the governing pressure vessel or piping code rather than assumed.

Corrosion Resistance in Chloride Service

2205 resists pitting, crevice corrosion and chloride stress corrosion cracking far better than Type 316L, and it performs well in seawater, brines and many dilute acids. Its limits should nevertheless be respected. In chloride-bearing service the grade is normally applied below about 150 °C, and in seawater it requires flowing conditions, since stagnant or poorly drained crevices can initiate attack. Critical pitting temperatures measured in standard ferric chloride testing are substantially higher than those of austenitic grades, which is why 2205 has become a default material for offshore, desalination and chemical process equipment. Where maximum resistance to chlorides is required, the super duplex grade 2507 takes over.

Fabrication, Welding and Typical Applications

Solution anneal in the range 1020-1100 °C and quench rapidly in water to restore the phase balance.

Avoid holding the material between roughly 300 °C and 950 °C, where intermetallic phases such as sigma can form and destroy toughness.

Weld with a matching duplex filler such as ER2209, keep heat input between about 0.5 and 2.5 kJ/mm and limit interpass temperature to about 150 °C.

The grade cold forms well, but it work hardens more than austenitic steels, so generous bend radii and intermediate annealing are advisable for severe forming.

Typical uses include oil and gas flowlines and manifolds, chemical storage tanks, offshore platform structures, desalination plant piping, pulp and paper digester equipment, heat exchangers and flue gas desulphurisation systems.

Frequently Asked Questions

Q: Is 2205 stainless steel magnetic?
Yes. The ferritic half of the duplex structure makes the grade magnetic, unlike fully austenitic grades such as 304 and 316.

Q: How much stronger is 2205 than Type 316?
The minimum 0.2 % yield strength is 450 MPa, roughly double the 316 requirement. That allows thinner sections for the same design pressure, which reduces weight and often cost.

Q: Can 2205 be used in seawater?
It performs well in flowing seawater and in many marine applications, but stagnant conditions and shielded crevices are a risk. Where low flow rates or higher temperatures apply, a super duplex grade is the safer choice.

Q: What is the difference between UNS S31803 and UNS S32205?
They describe the same family of grade. S32205 has tighter molybdenum and nitrogen ranges that guarantee a higher pitting resistance equivalent, and it has largely replaced S31803 in current specifications.

Q: Why must the welding procedure be qualified?
Welding changes the austenite and ferrite balance. A qualified procedure with controlled heat input, the correct filler and a limited interpass temperature keeps that balance within the range that preserves corrosion resistance and toughness.

Q: What temperature range should be avoided during processing?
Holding the material between roughly 300 °C and 950 °C for extended periods promotes sigma and other intermetallic phases, so heat treatment and hot working schedules must move through that window quickly.

Send Inquiry