ASTM A240 Stainless Steel Sheet Specification: Ratings, Tolerances and Density

Nov 13, 2025

Leave a message

astm-a240-Standard-Specification.pdf.pdf

What ASTM A240 Covers

ASTM A240/A240M is the standard specification for chromium and chromium-nickel stainless steel plate, sheet and strip for pressure vessels and for general applications. It is a product specification: it defines chemical composition, mechanical properties, dimensional tolerances, surface finish and testing requirements for the flat-rolled product itself. It does not rate a finished pressure vessel or a piping circuit, and it does not define a maximum working pressure.

The most frequently ordered grades include 304 and 304L (UNS S30400 and S30403), 316 and 316L (UNS S31600 and S31603), 321 (UNS S32100), 347 and 310S (UNS S31008). Buyers usually pair A240 with ASTM A480/A480M, which supplies the general requirements for flat-rolled stainless products, including thickness tolerances and permissible variations. The specification also permits a large number of heat-treatment and testing options that must be stated on the purchase order, otherwise the mill applies the default requirements.

Pressure Rating of ASTM A240 Material

ASTM A240 does not contain a pressure rating table, because plate and sheet are not pressure components. The allowable stress used to size a vessel or a pipe wall is taken from the design code: ASME Boiler and Pressure Vessel Code Section VIII Division 1, reading material values from Section II Part D at the design temperature.

The table below shows representative ambient-temperature design-strength levels for common A240 grades at a given thickness. They illustrate the thickness and grade trend only; the actual allowable stress must be taken from the applicable design code at the actual design temperature, with the appropriate joint efficiency and corrosion allowance.

Grade Typical Thickness Representative Pressure Level
304 / 304L 0.125 in (3.2 mm) Up to about 3,000 psi (20.7 MPa)
316 / 316L 0.125 in (3.2 mm) Up to about 3,000 psi (20.7 MPa)
321 0.250 in (6.35 mm) Up to about 2,500 psi (17.2 MPa)
310S 0.250 in (6.35 mm) Up to about 2,000 psi (13.8 MPa)

Two design consequences follow from the table. First, thickness rather than grade is the dominant variable in hoop-stress calculations, so a heavier 304L plate can outperform a thinner 316L plate at ambient temperature. Second, grade selection is driven by corrosion and temperature rather than by ambient strength; the mechanical advantage of higher-alloy grades appears mainly at elevated temperature, where creep and oxidation control the design.

Thickness Tolerance under A240 and A480

Thickness tolerance is one of the most quoted A240 parameters, and it is the source of most quantity disputes. Under ASTM A240 with the general requirements of A480, permissible thickness variation is banded by product thickness.

Specification Thickness Range Typical Thickness Tolerance Notes
ASTM A240 / A480 Up to 0.187 in (up to 4.75 mm) plus or minus 0.010 in (plus or minus 0.25 mm) Thinner sheets and plates
ASTM A240 / A480 0.188 to 0.500 in (4.76 to 12.7 mm) plus or minus 0.015 in (plus or minus 0.38 mm) Medium thickness range
ASTM A240 / A480 Over 0.500 in (over 12.7 mm) plus or minus 0.030 in (plus or minus 0.76 mm) Heavier plates

For a specification review, three practical points matter. Tolerance is applied to the ordered nominal thickness, not to a designer's minimum required thickness, so a marginally over-thin plate can still be compliant. Width and length tolerances, camber and flatness are also controlled by A480 and should be quoted when flat panels are laser cut or welded automatically. Finally, closer-than-standard tolerances can be ordered, but they raise cost and lead time and must be confirmed on the mill order.

Density and Weight Calculation

The density of the austenitic grades covered by A240 is approximately 7.9 g/cm3 (7,900 kg/m3) for 304, and slightly higher, about 7.98 g/cm3, for 316 because of its molybdenum and higher nickel content. Density is used directly for weight, freight and lifting calculations.

For flat product the useful formula is: weight (kg) = thickness (mm) x width (m) x length (m) x density (g/cm3). A practical example: one square metre of 3 mm type 304 sheet weighs 3 x 1 x 1 x 7.9 = 23.7 kg, while the same panel in 316 weighs about 23.9 kg. On a 20-tonne order these small differences are visible in the shipping documents, which is why density is normally taken from the governing specification rather than from a round number.

304 and 304L: about 7.9 g/cm3

316 and 316L: about 7.98 g/cm3

321: about 7.9 g/cm3

310S: about 7.9 g/cm3

Temperature Range of A240 Stainless Steel

A240 grades perform over a wide temperature band. The practical limits below reflect continuous operating service; short-term excursions and code-based design limits may differ.

Grade Low Temperature Limit High Temperature Limit
304 / 304L -196 C (-320 F) About 870 C (1,600 F)
316 / 316L -196 C (-320 F) About 870 C (1,600 F)
321 -196 C (-320 F) About 900 C (1,650 F)
310S -196 C (-320 F) About 1,150 C (2,100 F)

Three cautions apply in service. The low-carbon grades 304L and 316L retain toughness at cryogenic temperature, which is why they are used for liquefied gas service, but their elevated-temperature strength is lower than the standard-carbon versions. Grade 321 is stabilised with titanium and resists sensitisation during prolonged exposure in the 425 to 815 C range. Grade 310S is selected for the hottest applications such as furnace parts and radiant tubes, where its high chromium and nickel content provides oxidation resistance. In the 425 to 815 C band, carbon-bearing grades can sensitise at welds and heat-affected zones, so low-carbon or stabilised grades should be chosen where intergranular corrosion is a risk.

Frequently Asked Questions

Q: What is ASTM A240?
ASTM A240/A240M is the standard specification for chromium and chromium-nickel stainless steel plate, sheet and strip for pressure vessels and general applications. It controls composition, mechanical properties, tolerances and finish of the flat-rolled product.

Q: Does ASTM A240 specify a pressure rating?
No. A240 covers flat-rolled product rather than finished components, so it contains no pressure rating. The allowable stress used to design a vessel or pipe comes from the applicable design code, such as ASME Boiler and Pressure Vessel Code Section VIII.

Q: What thickness tolerance applies to A240 sheet and plate?
Under A240 with the general requirements of A480, tolerance is typically plus or minus 0.010 in (0.25 mm) up to 0.187 in thick, plus or minus 0.015 in (0.38 mm) from 0.188 to 0.500 in, and plus or minus 0.030 in (0.76 mm) above 0.500 in.

Q: What is the density of A240 stainless steel?
Type 304 is about 7.9 g/cm3 and type 316 about 7.98 g/cm3. These figures are used directly for weight calculation, and they should be taken from the governing specification rather than estimated.

Q: What temperature range can A240 stainless steel handle?
Grades 304 and 316 are commonly used from -196 C to about 870 C, grade 321 to about 900 C and grade 310S to about 1,150 C, with the low-carbon versions preferred for cryogenic service.

Q: Can I order A240 material to closer tolerances or a special finish?
Yes. Closer thickness tolerances, specified surface finishes and additional testing can be ordered as supplementary requirements, but they increase cost and lead time and must be stated on the purchase order.

Send Inquiry