316Ti and 904L Chemical Reactor Vessel Design and Fabrication

Jun 24, 2025

Leave a message

Specifying 316Ti or 904L is only half of the material decision for an acid-service reactor vessel. The other half belongs to the fabricator and the designer: how much wall thickness is sacrificed to corrosion, whether the vessel is solid alloy or clad, how nozzles and agitator supports are welded, and what inspection evidence proves the finished shell will survive its design life. This article covers the design and fabrication route for reaction vessels built in titanium-stabilised 316Ti and in super austenitic 904L.

Design Basis for Acid Service Vessels

Design to a recognised pressure vessel code, typically ASME Boiler and Pressure Vessel Code Section VIII Division 1 or EN 13445, with allowable stresses taken from the code stress tables at the design temperature.

Add a corrosion allowance rather than relying on the code minimum thickness. Acid service usually justifies 1 to 3 mm on wetted surfaces, with the larger figure where velocity, entrainment or frequent cleaning accelerate metal loss.

Set the design temperature above the highest credible process and cleaning temperature, including steam-out and chemical cleaning cycles.

Confirm the material against the vessel code: 316Ti plate is covered by ASTM A240, while 904L plate and sheet are specified under ASTM B625 with pipe under ASTM B673 and B677, so the material certificate must match the code under which the vessel is designed.

Material Selection by Service Condition

Process condition Recommended vessel material
Sulphuric acid at low concentration and near ambient temperature 316Ti
Sulphuric acid at moderate to high concentration, warm to hot 904L
Nitric acid, including hot and boiling duty 904L
Phosphoric acid and contaminated acid grades 904L
Mixed acids or acid streams with chloride or fluoride traces 904L
Organic acids at moderate temperature with low chloride 316Ti

When the process is strongly oxidising, when chlorides can concentrate in crevices, or when the wetted surface includes hot vapour spaces, 904L is the safer specification even if the liquid-phase analysis appears to suit 316Ti.

Shell, Head and Nozzle Fabrication

Roll and form plate with tooling dedicated to stainless steel to prevent iron contamination, and keep forming temperatures out of the sensitisation band for cold work.

Hot form heads and cones only within the recommended range, then solution anneal to restore corrosion resistance and remove forming strain.

Design nozzle reinforcement to the applicable code; nozzle-to-shell welds are the most common location for preferential attack, so full-penetration welds with smooth transitions are preferred.

For thick or high-pressure vessels, consider roll-bonded or weld-overlay clad plate instead of solid alloy, using 904L or 316Ti as the cladding and a carbon or low-alloy steel backing for strength.

Provide generous radii at internals, baffles and agitator supports so that cleaning fluids reach every surface and crevices are eliminated.

Corrosion Allowance and Thickness Control

Thickness is set from the code equation for circumferential or longitudinal stress, using the allowable stress at design temperature and the joint efficiency that reflects the radiographic examination applied. The corrosion allowance is then added to the calculated value and monitored over the vessel life. In practice the controlling number is the measured corrosion rate: with ultrasonic thickness readings taken at fixed datum points, the remaining life can be projected and the inspection interval adjusted to the measured loss rather than to a nominal allowance.

Welding, Heat Treatment and Surface Restoration

Qualify all procedures to ASME Section IX or EN ISO 15614-1, with procedure qualification covering the actual thickness range and positions used in the shop and in the field.

Weld 316Ti with ER316Ti to AWS A5.9 and 904L with ER385 to AWS A5.9; use ERNiCrMo-3 to AWS A5.14 for dissimilar and highly restrained joints, with buttering where carbon steel is involved.

Hold low heat input and cap interpass temperature at or below 100 °C, using stringer beads and no wide weaving.

Post-weld heat treatment is not required for either alloy. Solution annealing at 1040 - 1120 °C for 316Ti and 1100 - 1150 °C for 904L is reserved for material sensitised by hot forming or by an out-of-specification heat input.

Finish wetted surfaces by grinding, then pickle in accordance with ASTM A380 and passivate in accordance with ASTM A967; verify with a ferroxyl or equivalent free-iron test on critical surfaces.

Inspection, Testing and In-Service Monitoring

Volumetric examination of main seams by radiography, and surface examination by penetrant testing, in the proportions required by the vessel code.

Hydrostatic testing at the code-specified pressure, using water with controlled chloride content, followed by thorough drying of the vessel internals.

Ultrasonic thickness mapping at each internal inspection, at fixed datum points on shells, heads, nozzles and impingement zones.

Penetrant testing of welds at turnarounds, with particular attention to nozzle-to-shell junctions and support attachments.

Corrosion coupon exposure and electrochemical impedance spectroscopy where the process chemistry is variable, and electrochemical hydrogen permeation probes in hydrogen-generating service.

Positive material identification of plate, forgings and weld caps to confirm that no mixed material has entered the vessel.

Frequently Asked Questions

Q: How much corrosion allowance should an acid-service reactor vessel have?
Common practice is 1 to 3 mm on wetted surfaces, the higher figure where velocity, suspended solids or frequent chemical cleaning accelerate metal loss. The allowance is then adjusted from measured wall thickness data.

Q: Does a 316Ti vessel need post-weld heat treatment?
No. The titanium addition stabilises the grade against sensitisation, so post-weld solution annealing is unnecessary in most services and is reserved for material affected by hot forming or excessive heat input.

Q: Can 904L be used as cladding instead of solid plate?
Yes. Roll-bonded or weld-overlay clad plate with 904L on a carbon or low-alloy steel backing gives the corrosion performance of the alloy with the strength and cost structure of the backing steel.

Q: Which design codes apply to 316Ti and 904L reactor vessels?
ASME Section VIII Division 1 is the most common for cross-border projects, with EN 13445 as the European alternative. The material specification must be one accepted by the chosen code for the product form being purchased.

Q: What is the maximum design temperature for these vessel materials?
Roughly 400 °C for 316Ti and 450 °C for 904L in continuous acid service. Long exposure above about 600 °C risks sigma phase embrittlement in both alloys.

Q: How often should an acid-service reactor vessel be inspected?
The first internal inspection is typically carried out early in service to establish the corrosion rate, after which the interval is set from the measured wall loss, with ultrasonic thickness mapping and weld penetrant testing at each turnaround.

Send Inquiry