How Does 2507 Super Duplex Steel Outperform 2205 in Corrosion Resistance?
Dec 11, 2025
Leave a message
Grade 2507 is the standard super-duplex stainless steel, designated UNS S32750 in ASTM A240 and EN 1.4410 in European standards. Grade 2205, designated UNS S32205 (with the older UNS S31803), is the most widely used duplex grade. Both combine an austenitic-ferritic microstructure with roughly twice the yield strength of 304 or 316 austenitic grades. The difference in corrosion resistance between them is not marginal: it is a systematic consequence of higher chromium, molybdenum, nickel and nitrogen in 2507.
This article compares the two grades on the basis of standard composition limits and mechanical minimums, explains why higher PREN values translate into measurable field performance, and provides practical selection guidance for marine, oil and gas, chemical and desalination service.
Chemical Composition: UNS S32750 vs UNS S32205
The composition below follows ASTM A240 limits for plate, sheet and strip. The same limits apply to bar, forgings and pipe through ASTM A182, A479, A789 and A790.
| Element (wt%) | 2507, UNS S32750 | 2205, UNS S32205 |
|---|---|---|
| Carbon, max | 0.030 | 0.030 |
| Chromium | 24.0–26.0 | 22.0–23.0 |
| Nickel | 6.0–8.0 | 4.5–6.5 |
| Molybdenum | 3.0–5.0 | 3.0–3.5 |
| Nitrogen | 0.24–0.32 | 0.14–0.20 |
| Manganese, max | 1.20 | 2.00 |
| Silicon, max | 0.80 | 1.00 |
| Phosphorus, max | 0.035 | 0.030 |
| Sulfur, max | 0.020 | 0.020 |
Chromium, molybdenum and nitrogen are the elements that build the passive film and repair it after damage. Grade 2507 raises all three, and the combination has a multiplicative effect on localized corrosion resistance rather than an additive one.
PREN and Localized Corrosion Behaviour in Chloride Media
The pitting resistance equivalent number is the standard engineering screening tool for chloride pitting and crevice corrosion:
PREN = Cr + 3.3 x Mo + 16 x N
Using the mid-range composition of each grade, 2507 gives roughly 25 + 3.3 x 4 + 16 x 0.28, or about 43, while 2205 gives about 22.5 + 3.3 x 3.25 + 16 x 0.17, or about 36. Typical published PREN values are above 40 for 2507 and 34 to 36 for 2205. In practice this means 2507 tolerates significantly higher chloride concentrations and temperatures before pitting or crevice corrosion initiates, which is the dominant factor in seawater, brine and produced-water systems.
Pitting starts where the passive film breaks down locally; crevice corrosion starts in stagnant gaps under gaskets, deposits and scale. Both are governed by the same alloying logic as PREN. In marine service, 2205 is widely used for splash-zone and less severe applications, while 2507 is specified where seawater is pumped, heated or stagnant, such as seawater-cooled heat exchangers, firewater systems and desalination plant piping. The critical pitting temperature of 2507 measured in standard ferric-chloride tests is markedly higher than that of 2205 in the same test solution, which is why 2507 appears in the most severe sections of offshore water-handling systems.
Resistance to Chloride Stress Corrosion Cracking
Chloride stress corrosion cracking is the failure mode that eliminates most austenitic grades in hot chloride service. The duplex microstructure itself is the first line of defence: the ferrite phase resists crack propagation, and the balanced austenite-ferrite ratio distributes stress. The higher alloy content of 2507 further raises the threshold temperature and chloride level at which cracking can occur. This is a critical advantage in downhole oil and gas equipment, subsea components and marine propulsion shafts, where both pitting and SCC resistance are required simultaneously.
Mechanical Properties: Higher Strength at the Same Time
Corrosion resistance is not the only difference. Per ASTM A240, solution-annealed minimums are:
| Property | 2507, UNS S32750 | 2205, UNS S32205 |
|---|---|---|
| Tensile strength, min (MPa) | 795 | 655 |
| 0.2% yield strength, min (MPa) | 550 | 450 |
| Elongation in 50 mm, min (%) | 15 | 25 |
| Hardness, max (HB) | 310 | 293 |
The higher strength of 2507 allows thinner sections for the same design pressure, which partially offsets its higher alloy cost. The trade-off is that 2507 demands tighter control in forming and welding, and its lower elongation must be respected in expansion and flaring operations.
Where to Specify 2507 Instead of 2205
Specify 2507 when the environment combines chlorides with heat, pressure or crevices: seawater heat exchangers and condensers, subsea manifolds, firewater deluge systems, flue-gas desulfurization scrubbers, evaporators, and production tubulars for sour service under ISO 15156. Specify 2205 when the chloride load is moderate, when the design is governed by fatigue or fabrication cost, or when existing welding procedures and qualified materials are already in place for 2205.
FAQ
Is 2507 always better than 2205?
No. 2507 offers higher corrosion resistance and strength but costs more, is harder to form, and requires qualified welding procedures. For moderate chloride service, 2205 is often the more economical and practical choice.
What PREN is needed for seawater service?
As a rule of thumb, PREN above 40 is preferred for continuous seawater exposure at ambient temperature, which is why 2507 is common in seawater piping. 2205, with a PREN near 35, is used in less severe or intermittent seawater duty and in splash zones where crevices are minimized by design.
Can 2507 suffer chloride stress corrosion cracking?
Yes, in extreme conditions. No duplex grade is immune: very high chloride concentrations, temperatures above about 150 C and high tensile stress can still initiate cracking. 2507 simply moves the threshold far beyond the range where 2205 and austenitic grades fail.
How is corrosion resistance maintained after welding?
Welding must preserve the balanced austenite-ferrite ratio. Use over-alloyed filler such as UNS S32750 or nickel-base UNS N06625 filler where required, control interpass temperature, and verify weld metal by ferrite measurement and hardness testing per ASTM A923 and ASTM A928 practice.
Can 2507 replace 2205 in an existing design?
Only after re-verification. Wall thickness can usually be reduced because of higher strength, but the welding procedure, NDT plan and sour-service qualification per ISO 15156 must be re-qualified for the new grade.
Send Inquiry






