Stainless Steel 1.4571 vs 316: Titanium-Stabilized Grade Comparison
May 12, 2025
Leave a message
What Is Stainless Steel 1.4571 (316Ti)?
Stainless steel 1.4571 is the EN material number for the titanium-stabilized austenitic grade that is also written as X6CrNiMoTi17-12-2, UNS S31635 and 316Ti. It keeps the chromium-nickel-molybdenum base of 316 stainless steel (EN 1.4401, UNS S31600) and adds titanium, which changes how the material behaves during welding and in elevated-temperature service.
Both grades are austenitic steels with a face-centred cubic structure. In the annealed condition they are non-magnetic, offer good toughness down to cryogenic temperatures, and can be cold formed, machined and polished with conventional workshop practice. Molybdenum is the element that gives both grades their resistance to pitting and crevice corrosion in chloride-bearing media, which is why they appear throughout chemical plants, marine hardware and process piping.
The real question is rarely which grade is stronger. At room temperature the two are practically interchangeable in strength and ductility. The difference appears after welding, and after long exposure to heat: one grade keeps its corrosion resistance where the other can lose it at the grain boundaries.
Chemical Composition and Grade Equivalents
| Element | 316 (1.4401 / S31600) | 1.4571 (316Ti / S31635) |
|---|---|---|
| Carbon | 0.08% max | 0.08% max |
| Chromium | 16.0-18.0% | 16.5-18.5% |
| Nickel | 10.0-14.0% | 10.5-13.5% |
| Molybdenum | 2.0-3.0% | 2.0-2.5% |
| Titanium | not specified | 5 x C minimum, 0.70% max |
| Manganese | 2.00% max | 2.00% max |
| Silicon | 0.75% max | 0.75% max |
| Nitrogen | 0.10% max | 0.10% max |
Both grades are supplied under ASTM A240 (plate, sheet and strip), ASTM A276 (bars and shapes) and EN 10088-2 or EN 10088-3 in Europe. The titanium requirement is the only structural difference in the specification: 1.4571 must contain at least five times the carbon content in titanium, capped at 0.70%, so there is always enough titanium to combine with the carbon present.
Room-temperature mechanical requirements are also the same for both grades in the annealed condition: 515 MPa minimum tensile strength, 205 MPa minimum 0.2% yield strength, 40% minimum elongation in 50 mm, and 95 HRB maximum hardness. Choosing 1.4571 therefore delivers no strength advantage - the benefit is entirely metallurgical.
Titanium Stabilization and Intergranular Corrosion
When an unstabilized austenitic steel such as 316 is held in the sensitization range of roughly 425-815 C, carbon in solid solution migrates to the grain boundaries and precipitates as chromium-rich carbides. Each carbide particle consumes chromium from the surrounding matrix, leaving a narrow chromium-depleted zone. In a corrosive medium that zone dissolves first, and the steel fails by intergranular corrosion.
Titanium has a stronger affinity for carbon than chromium does. In 1.4571 the titanium forms stable titanium carbides during melting and annealing at temperatures well above the sensitization range, so there is almost no dissolved carbon left to precipitate later. Even if a welded joint or a hot component passes through 425-815 C, the grain boundaries stay protected.
Two practical consequences follow. First, 1.4571 tolerates slow cooling through the sensitization range, which 316 does not. Second, the titanium addition only stabilizes the steel - it does not raise the general corrosion resistance, so in a chloride-rich medium both grades still depend on the chromium-molybdenum passive film.
One limitation is worth knowing before specifying the grade. In strongly oxidizing media such as hot nitric acid, stabilized grades can suffer knife-line attack immediately beside a weld, because the titanium-rich carbides themselves are attacked. For such service, low-carbon grades or alternative alloying concepts are normally chosen instead.
High-Temperature Performance and Weldability
316 is a common choice for process equipment, yet its useful continuous service temperature is limited when the environment is corrosive and the exposure is long. Above about 425 C, sensitization begins to work against the grade in the heat-affected zone of a weld and in the parent metal of hot sections.
1.4571 extends that practical range. Because the carbon is already locked up, the material keeps its intergranular corrosion resistance through the 425-815 C band, and it is a standard selection for components that cycle repeatedly through that temperature interval. Where the requirement is simply high-temperature strength without a corrosive medium, 316H (UNS S31609) with a higher carbon content is the usual alternative, since carbon improves creep resistance.
From a welding standpoint both grades are easy to join by TIG, MIG and shielded metal arc processes. The key difference is post-weld treatment. A 316 joint that will operate in a corrosive environment often needs solution annealing after welding to restore the depleted zone, which is impossible on large fabricated assemblies. A 1.4571 joint does not need that treatment, which is exactly why it is specified for field-welded tanks, coils and pipework.
Use 316 where the service temperature stays below the sensitization range and welds are light or can be annealed.
Use 1.4571 where welds are heavy, post-weld heat treatment is impractical, or service temperature falls in the 425-815 C band.
Use 316L (1.4404) as a low-carbon alternative for welded components in corrosive media at moderate temperature.
Use 316H where creep and high-temperature strength - not sensitization - drive the design.
Typical Applications of 1.4571 and 316
316 stainless steel remains the workhorse grade for general corrosion service: marine hardware and fasteners, chemical storage tanks, food and beverage processing equipment, architectural cladding and kitchen equipment. It balances corrosion resistance, formability and cost better than almost any other austenitic grade.
1.4571 takes over where heat and welding combine: heat exchangers and tube bundles, furnace components and muffle supports, pressure vessels, expansion joints, exhaust systems, and piping in high-temperature or mildly acidic service. It is also common in the pulp and paper industry, where hot alkaline and acidic liquors and welded construction are both present.
For both grades, selection should be confirmed against the actual medium, chloride level, temperature and welding procedure, because no single austenitic grade covers every combination of those variables.
Frequently Asked Questions
Q: Is 1.4571 the same as 316Ti?
Yes. 1.4571 is the EN material number, 316Ti is the common AISI-style designation and UNS S31635 is the unified numbering system code for the same titanium-stabilized austenitic stainless steel.
Q: What is the difference between 1.4571 and 1.4401?
1.4401 is standard 316 with no titanium; 1.4571 is the titanium-stabilized version. They have the same base chemistry, but 1.4571 resists intergranular corrosion after welding or hot service while 1.4401 relies on low carbon or post-weld annealing.
Q: Is 1.4571 stainless steel magnetic?
In the annealed condition it is essentially non-magnetic because its structure is austenitic. Severe cold working such as heavy bending or drawing can form a small amount of martensite, which produces a weak magnetic response - this is normal and is not a defect.
Q: Can 1.4571 replace 316L?
In many welded, high-temperature applications yes, and it is often preferred because the titanium stabilization does not depend on very low carbon. For strongly oxidizing acid service, low-carbon grades are usually specified instead because of possible knife-line attack.
Q: What temperature range causes sensitization in 316 stainless steel?
Chromium carbide precipitation occurs mainly between about 425 C and 815 C. Time at temperature matters as much as the temperature itself, so slow cooling through this band is more damaging than a brief pass.
Q: Which grade is better for a marine or high-chloride environment?
Both resist chloride pitting far better than 304 because of their molybdenum content, and 316 is the standard choice for marine hardware. For continuously wet seawater or hot concentrated chlorides, a higher-molybdenum austenitic grade or duplex stainless steel such as UNS S32205 is normally required.
Send Inquiry






