EN 1.4539 (904L) Super Austenitic Stainless Steel: Properties, Composition and Applications

May 22, 2025

Leave a message

What EN 1.4539 Actually Is

EN 1.4539 is the European material number for a super austenitic stainless steel listed in EN 10088-2, where it also carries the steel name X1NiCrMoCu25-20-5. The same alloy is known as grade 904L in commercial practice and as UNS N08904 in ASTM and ASME product standards, so a purchase order quoting EN 1.4539, 904L or UNS N08904 is normally asking for one and the same material, provided the product form and the specified standard match.

What separates this grade from ordinary 18-8 stainless steel is alloy content. High nickel keeps the structure fully austenitic and slows chloride stress corrosion cracking; chromium forms the passive surface film; molybdenum and copper raise resistance to reducing acids such as sulphuric and phosphoric acid. The result is a material that holds up in environments where Type 316L fails within months.

Chemical Composition per EN 10088-2

Element Requirement (%) Function
Carbon (C) ≤ 0.020 Keeps carbon low to limit sensitisation
Silicon (Si) ≤ 1.00 Deoxidation
Manganese (Mn) ≤ 2.00 Structural stabiliser
Phosphorus (P) ≤ 0.030 Impurity control
Sulphur (S) ≤ 0.010 Impurity control, weldability
Chromium (Cr) 19.0 - 21.0 Passive film, oxidation resistance
Nickel (Ni) 24.0 - 26.0 Austenite stability, SCC resistance
Molybdenum (Mo) 4.0 - 5.0 Pitting and crevice corrosion resistance
Copper (Cu) 1.20 - 2.00 Resistance to reducing acids
Nitrogen (N) ≤ 0.15 Strength and pitting resistance
Iron (Fe) Balance Matrix

The molybdenum-chromium-nitrogen balance gives a pitting resistance equivalent number of roughly 35, calculated as Cr + 3.3 Mo + 16 N. Type 316L sits near 25 on the same scale, which is the single most useful number when comparing the two grades for chloride service.

Mechanical Properties of Solution-Annealed Product

Property Value (annealed) Test Standard
Tensile strength, Rm 520 - 720 MPa EN ISO 6892-1 / ASTM A370
0.2% proof strength, Rp0.2 ≥ 230 MPa EN ISO 6892-1 / ASTM A370
Elongation, A ≥ 35% EN ISO 6892-1 / ASTM A370
Hardness approx. 150 - 200 HBW ISO 6506-1 / ASTM E10
Modulus of elasticity approx. 195 GPa EN 10088-2 reference data

Two cautions matter to buyers. First, strength figures of 850 MPa and above that circulate for this grade describe cold-worked or cast product; they must not be used as the design basis for annealed plate, sheet or tube, which is governed by the 520 to 720 MPa band. Second, the grade is supplied non-magnetic when annealed and becomes slightly magnetic after heavy cold forming.

Corrosion Performance in Service

Chloride pitting and crevice corrosion: the high molybdenum and nitrogen content raises the critical pitting temperature well above that of Type 316L, which allows use in brackish and seawater-bearing circuits where 316L pits.

Stress corrosion cracking: nickel above 20% substantially improves resistance to chloride SCC compared with 18-8 grades, although the alloy is not immune at elevated temperature and high chloride concentration.

Reducing acids: copper additions give useful resistance to sulphuric and phosphoric acid over wide concentration and temperature ranges, which is why the grade dominates phosphoric acid evaporator service.

Intergranular corrosion: low carbon plus a solution anneal makes sensitisation unlikely; qualification is normally demonstrated by ASTM A262 Practice E or ISO 3651-2.

Where the Grade Is Used

Chemical and petrochemical plants: reactors, storage tanks, acid piping, agitators and heat exchanger tubing.

Flue gas desulphurisation absorbers, ducting and mist eliminators in power generation.

Offshore and marine systems: seawater piping, condensers, pump bodies and platform hardware exposed to salt spray.

Pulp and paper bleaching lines and digester equipment handling chloride-bearing liquors.

Pharmaceutical, food and beverage plant: fermentation tanks, dairy pipelines and clean-in-place circuits.

Desalination and waste water treatment: brine lines, digesters and evaporator stages.

Forms, Standards and Procurement Notes

Plate, sheet and strip: EN 10088-2, ASTM A240, ASTM B625, ASME SB625.

Bar and wire: ASTM B649, ASME SB649.

Welded pipe and tube: ASTM B673 and ASTM B677; seamless tube and pipe: EN 10216-5, ASTM B674 and ASTM B706.

Fittings and flanges are produced to the corresponding ASTM B366 wrought fitting and B564 forging specifications for the grade family.

Insist on mill test certificates to EN 10204 3.1 or 3.2 that state the heat number, the standard edition applied and the actual chemistry, not just nominal values.

Because the alloy work-hardens quickly, specify the delivered condition as solution annealed unless a cold-worked strength level is genuinely required.

Allow longer lead times than for 316L; the grade is produced in fewer mills and special sizes are frequently made to order.

Frequently Asked Questions

Q: Is EN 1.4539 the same material as 904L?
Yes. EN 1.4539 and X1NiCrMoCu25-20-5 are the European names, 904L is the long-established commercial name and UNS N08904 is the unified numbering system designation used in ASTM and ASME product standards. The three designations refer to the same alloy chemistry.

Q: How does EN 1.4539 compare with Type 316L?
Both are austenitic and non-magnetic when annealed, but EN 1.4539 contains far more nickel, molybdenum and copper. That raises its pitting resistance equivalent number to about 35 against roughly 25 for 316L, giving markedly better performance in chlorides and reducing acids at a higher purchase price.

Q: Can EN 1.4539 be welded in the field?
Yes. Gas tungsten arc and gas metal arc welding are both suitable. Use a matching or nickel-base filler, keep heat input low, avoid excessive interpass temperature and clean the joint thoroughly, because residual iron contamination is the usual cause of early rusting on this grade.

Q: What is the maximum service temperature?
Pressure equipment codes allow continuous service up to roughly 425 degrees Celsius. Above that level the mechanical property allowances fall and oxidation becomes the limiting factor, so high-temperature designs usually select a different alloy family.

Q: Is the material magnetic?
Annealed product is essentially non-magnetic. Cold working such as bending, drawing or machining converts part of the austenite to martensite and produces a weak magnetic response, which does not indicate a defective or incorrect grade.

Q: Which product forms are readily available?
Plate, sheet, round bar, seamless and welded pipe and tube, plus machined fittings and flanges. Availability of heavy plate and large diameter seamless tube is tighter than for 316L, so early order placement is advisable for project schedules.

Send Inquiry