HS Code for ASTM A312 Stainless Steel Pipe: 730441 and 730431 Classification
May 27, 2025
Leave a message
What Is the HS Code for ASTM A312 Stainless Steel Pipe?
ASTM A312 / A312M is the standard specification for seamless, welded and heavily cold worked austenitic stainless steel pipe intended for high-temperature and general corrosive service. When that pipe crosses a border, customs authorities classify it inside the Harmonized System (HS), the six-digit nomenclature maintained by the World Customs Organization. For ASTM A312 stainless steel pipe the correct heading is 730441 - tubes, pipes and hollow profiles, seamless, of stainless steel, obtained by cold drawing or cold rolling.
The grade designation never changes the six-digit code. HS classification tracks product form, manufacturing route and material family, not the individual steel grade. A shipment of ASTM A312 TP316L and a shipment of ASTM A312 TP304 therefore clear under the same heading, provided both are seamless products.
730441 or 730431: Seamless Versus Welded Tube
The most frequent classification error on A312 shipments is mixing up the seamless and welded routes. ASTM A312 covers both, but the tariff treats them separately. Seamless pipe produced by piercing and cold drawing stays in 730441. Pipe made from strip or coil and longitudinally welded, with or without a subsequent cold finishing pass, belongs to 730431.
| Product form | Manufacturing route | HS heading | Typical grades |
|---|---|---|---|
| Seamless pipe | Hot finished, then cold drawn if required | 730441 | TP304, TP304L, TP316, TP316L, TP321, TP347 |
| Seamless tube, small OD | Cold drawn and bright annealed | 730441 | TP304L, TP316L |
| Welded pipe, longitudinal | Strip formed and welded, circular section | 730431 | TP304, TP316, TP316L |
| Welded and cold worked pipe | Welded first, then cold reduced | 730431 | TP304L, TP316L |
A welded origin is retained even when the tube is later cold worked, because the tariff follows the primary forming operation rather than the final surface condition.
Why Grades, Sizes and Finish Do Not Move the Heading
Buyers often assume that a higher alloy content automatically means a different HS code. It does not. The six-digit heading describes the product, so the following variables leave 730441 and 730431 untouched:
Grade: TP304, TP304L, TP316, TP316L, TP321, TP347 and TP347H all sit inside the austenitic family described by ASTM A312.
Outside diameter and wall thickness: schedule 10S, 40S, 80S or a custom metric size are all the same product.
Surface finish: pickled, bright annealed, polished or shot blasted.
End preparation: plain end, bevelled end or threaded.
Length: random length, double random length or cut to a fixed length.
What does matter is the metal itself. Pipe made of carbon steel, alloy steel or a non-ferrous metal falls in an entirely different heading, and a stainless steel pipe that is not round in cross-section also leaves these headings.
National Tariff Extensions: 8-Digit and 10-Digit Codes
Most customs territories expand the six-digit HS code into eight, ten or even twelve digits to reflect duty rates and statistical needs. The extension differs from country to country, so the same ASTM A312 pipe can carry a different national number at the destination even though the first six digits are identical.
| Digits | Level | What the extension captures |
|---|---|---|
| 6 | World Customs Organization | Product family: seamless or welded stainless steel tube |
| 8 | National tariff line | Outside diameter ranges, wall thickness classes |
| 10 | Statistical or duty line | End use, pressure service, specific industry programmes |
For an accurate duty calculation, the six-digit heading must be paired with the national extension in force at the country of importation, together with the applicable anti-dumping or safeguard measures that may apply to stainless steel tubular products.
Documents That Support the Declaration
Customs officers rarely accept a verbal description. A clean declaration for ASTM A312 pipe normally carries an ASTM A312 / A312M mill certificate with the heat number, grade, dimensions and mechanical test results, a commercial invoice that states the product form, a packing list, and a manufacturer's declaration of the country of origin. Where the buyer requests it, a third-party inspection certificate can accompany the same file.
Consistency is what prevents delays. When the invoice says seamless, the mill certificate must also say seamless, because a mismatch between the stated product form and the heading declared is the trigger for inspection and reclassification.
FAQ
Q: What is the HS code for ASTM A312 stainless steel pipe?
Seamless ASTM A312 pipe is classified under HS heading 730441. Welded ASTM A312 pipe is classified under HS heading 730431.
Q: Does the grade TP316L change the HS code?
No. Grade has no effect on the six-digit heading. TP304, TP316 and TP316L seamless pipe all fall under 730441.
Q: Why do some invoices show 73044110 or 73044190?
Those are national extensions of the six-digit heading. They subdivide seamless stainless steel tube by outside diameter, wall thickness or end use.
Q: Does a cold drawn welded tube stay in 730431?
Yes. Cold working after welding does not change the primary forming route, so the product remains under 730431.
Q: Is heat exchanger tubing classified differently from pipe?
Not at the six-digit level. The distinction between pipe and tube in ASTM A312 is dimensional and end-use driven, while the tariff follows the seamless or welded route.
Q: What information is needed for an exact local code?
The country of importation, the exact outside diameter and wall thickness, the grade, and whether the product is seamless or welded.
Send Inquiry






