ANSI/ASME B36.10M、B36.19M Thickness Data Table

ANSI/ASME B36.10M,B36.19M Thickness data table

Nominal size (inches)	sch5s	sch10s	sch10	sch20	sch30	sch40s	STD	sch40	sch60	sch80s	XS	sch80	sch100	sch120	sch140	sch160	XXS	sch160s
1/8	10.29	-	1.24	-	-	1.73	1.73	1.73	2.41	2.41	2.41	-	-	-	-	-	-	-
1/4	13.72	-	1.65	-	-	2.24	2.24	2.24	3.02	3.02	3.02	-	-	-	-	-	-	-
3/8	17.15	-	1.65	-	-	2.31	2.31	2.31	3.20	3.20	3.20	-	-	-	-	-	-	-
1/2(15)	21.34	1.65	2.11	-	-	2.77	2.77	2.77	3.73	3.73	3.73	-	-	-	4.78	7.47	4.78	-
3/4(20)	26.67	1.65	2.11	-	-	2.87	2.87	2.87	3.91	3.91	3.91	-	-	-	5.56	7.82	5.56	-
1(25)	33.40	1.65	2.77	-	-	3.38	3.38	3.38	4.55	4.55	4.55	-	-	-	6.35	9.09	6.35	-
1 1/4(32)	42.16	1.65	2.77	-	-	3.56	3.56	3.56	4.85	4.85	4.85	-	-	-	-	9.70	-	-
1 1/2(40)	48.26	1.65	2.77	-	-	3.68	3.68	3.68	5.08	5.08	5.08	-	-	-	-	7.14	15.15	7.14
2(50)	60.33	1.65	2.77	-	-	3.91	3.91	3.91	5.54	5.54	5.54	-	-	-	-	9.14	11.07	8.74
2 1/2(65)	73.03	2.11	3.05	-	-	5.16	5.16	5.16	7.01	7.01	7.01	-	-	-	-	9.53	14.02	9.53
3(80)	88.90	2.11	3.05	-	-	5.74	5.74	5.74	7.62	7.62	7.62	-	-	-	-	11.13	15.24	11.13
3 1/2(90)	101.60	2.11	3.05	-	-	6.02	6.02	6.02	8.56	8.56	8.56	-	-	-	11.12	13.49	17.12	13.49
4(100)	114.30	2.11	3.05	-	-	6.02	6.02	6.02	8.56	8.56	8.56	-	-	-	11.12	13.49	17.12	13.49
5(125)	141.30	2.77	3.40	-	-	6.55	6.55	6.55	9.53	9.53	9.53	-	-	-	12.70	15.88	19.05	15.88
6(150)	168.27	2.77	3.40	-	-	7.11	7.11	7.11	10.97	10.97	10.97	-	-	-	14.09	19.27	18.62	19.27
8(200)	219.08	2.77	3.76	6.35	7.04	8.18	8.18	9.18	13.20	12.70	12.70	15.09	19.26	20.62	23.81	22.23	23.81
10(250)	273.05	3.40	4.19	6.35	7.80	9.27	9.27	9.27	12.70	12.70	12.70	15.09	19.26	21.44	25.40	28.58	25.40
12(300)	323.85	3.96	4.67	6.35	8.38	9.53	9.53	10.31	14.27	12.70	12.70	17.48	21.44	25.40	28.58	33.32	25.40
14(350)	355.60	3.96	4.78	6.35	7.92	9.53	9.53	11.13	15.09	12.70	12.70	19.05	23.81	27.79	31.75	35.71	25.40
16(400)	406.40	4.19	4.78	6.35	7.92	9.53	9.53	12.70	16.66	12.70	12.70	21.44	28.39	30.96	35.53	40.49	25.40
18(450)	457.20	4.19	4.78	6.35	7.92	11.13	9.53	14.27	19.05	12.70	12.70	23.81	29.36	34.33	38.67	45.24	25.40
20(500)	508.00	4.78	5.54	6.35	9.53	12.70	9.53	15.09	20.62	12.70	12.70	26.19	32.54	38.10	44.45	50.01	25.40
22(550)	558.80	4.78	5.54	6.35	9.53	12.70	9.53	22.23	12.70	12.70	28.58	34.93	41.26	47.63	53.98	25.40	-
24(600)	609.60	5.54	6.35	6.35	9.53	14.27	9.53	17.48	24.61	12.70	12.70	30.96	38.89	46.02	52.37	59.54	-
26(650)	660.40	-	-	7.92	12.70	-	9.53	-	-	12.70	12.70	-	-	-	-	-	-	-
28(700)	711.20	-	-	7.92	12.70	-	9.53	-	-	12.70	12.70	-	-	-	-	-	-	-
30(750)	762.00	-	-	7.92	12.70	-	9.53	-	-	12.70	12.70	-	-	-	-	-	-	-
32(800)	812.80	6.35	7.92	7.92	12.70	-	9.53	17.48	12.70	12.70	-	-	-	-	-	-	-	-
34(850)	863.60	-	-	7.92	12.70	-	9.53	17.48	12.70	12.70	-	-	-	-	-	-	-	-
36(900)	914.40	-	-	7.92	12.70	-	9.53	19.05	12.70	12.70	-	-	-	-	-	-	-	-
40(1000)	1016.00	-	-	9.53	14.3	-	9.53	26.20	-	-	-	-	-	-	-	-	-	-

 

What is the difference between nominal and inch stainless steel pipes?

Nominal Size (DN):
Typically expressed in millimeters (mm), the nominal size refers to the approximate diameter or internal diameter of the pipe.
It is a nominal value, not the actual size of the pipe. For example, DN50 indicates the nominal diameter is approximately 50mm, but the actual outer diameter might be 60.3mm, depending on the wall thickness.
Nominal sizes are widely used in international standards, especially in Europe and Asia.

Inch Size (NPS):
Expressed in inches (inch), the inch size refers to the Nominal Pipe Size (NPS).
This naming convention is commonly used in imperial system countries like the United States.
For example, NPS 1 pipe has an actual outer diameter of 33.4mm, not 1 inch (25.4mm).