904L Plate Thickness Chart: EN 10088-2, ASTM B625 and JIS G4304

May 20, 2025

Leave a message

904L stainless steel plate is a super-austenitic, low-carbon grade used in chemical processing, marine engineering, pulp and paper plant and flue gas desulfurization systems. Because it is ordered against three different international systems, thickness ranges and tolerances must be matched to the standard named on the drawing: ASTM B625 in the United States and most international projects, EN 10088-2 in Europe, and JIS G4304 in Japan. This guide sets out the usual mill thickness ranges for each and compares the tolerances that apply.

What 904L Plate Is

904L is designated UNS N08904 in the ASTM system, EN 1.4539 in the European system and SUS 890L in the Japanese system. Its high nickel and molybdenum content gives it resistance to pitting, crevice corrosion and chloride stress corrosion cracking well beyond that of conventional 316L, while the low carbon level keeps the grade weldable without sensitization risk.

Element, % Typical 904L range
Nickel, Ni 23.0-28.0
Chromium, Cr 19.0-23.0
Molybdenum, Mo 4.0-5.0
Copper, Cu 1.0-2.0
Carbon, C max 0.020
Manganese, Mn max 2.00
Silicon, Si max 1.00

904L Plate Thickness Chart: Typical Mill Range

The table below shows the thickness bands normally held in stock or rolled to order, together with the surface condition and edge format typically supplied in each band. Light plate is the fastest to obtain; heavy plate is normally produced against a project order with a defined lead time.

Thickness, mm Common availability Standard format supplied
3.0-6.0 Readily available from stock Hot rolled, annealed and pickled
6.0-12.0 Standard plate size Hot rolled annealed and pickled, mill edge or cut edge
12.0-25.0 Custom or project based Heavy plate, cut to size by waterjet or plasma
25.0-50.0 Made to order Heavy plate, project lead time applies

Standard plate widths are 1,000 mm, 1,220 mm, 1,500 mm and 2,000 mm, and standard lengths are 2,000 mm, 2,440 mm and 3,000 mm, with custom cut lengths available on request.

Standards Governing 904L Plate

ASTM B625, UNS N08904

ASTM B625 covers 904L plate and sheet for the United States and for most international projects. It defines the chemical composition, mechanical properties and dimensional tolerances of the grade, and common plate thicknesses run from 3.0 mm to 50.0 mm. Thickness tolerance and flatness are generally taken from the referencing flat-product specification, with thickness tolerances running from about ±0.3 mm on light plate to ±1.5 mm on heavy plate, and flatness controlled against the relevant flatness table for hot rolled annealed and pickled product.

EN 10088-2, EN 1.4539

EN 10088-2 is the European standard for flat products of corrosion-resistant stainless steel and covers both hot rolled and cold rolled plate and sheet. It is the preferred reference for equipment built to CE marking and pressure equipment requirements. Thickness classes are usually grouped as thin plate from 3.0 to 6.0 mm, medium plate from 6.0 to 12.0 mm and heavy plate from 12.0 to 50.0 mm. Tolerances are taken from the hot rolled flat product tolerance standard, with thickness tolerances of roughly ±0.3 mm to ±2.0 mm, and flatness of 10 mm/m in the standard class or 5 mm/m in the special class.

JIS G4304, SUS 890L

JIS G4304 is the Japanese standard for hot rolled stainless steel plate, sheet and strip, and the corresponding designation for 904L is SUS 890L. The thickness range normally covered is 3 mm to 25 mm, with thickness deviation of about ±0.4 mm to ±1.2 mm and width and length tolerances taken from the standard tables or from the agreed mill specification.

Thickness Tolerance Comparison

The comparison below shows how much tolerance the three systems allow in each thickness band. For a given plate, the European standard is the most generous at the heavy end, while the Japanese standard is the tightest, so the standard named on the drawing has a direct effect on the mass and the fit-up of the finished component.

Thickness, mm ASTM tolerance EN tolerance JIS tolerance
3.0-6.0 ±0.3 to ±0.4 mm ±0.4 mm ±0.4 mm
6.0-12.0 ±0.5 to ±0.8 mm ±0.6 to ±0.8 mm ±0.6 mm
12.0-25.0 ±1.0 to ±1.2 mm ±1.0 mm ±1.0 mm
25.0-50.0 ±1.5 mm ±2.0 mm ±1.2 mm

Ordering Notes and Dimensional Formats

State the governing standard explicitly, because the same nominal thickness carries different tolerances under ASTM, EN and JIS.

Specify the delivery condition: hot rolled annealed and pickled is standard, while cold rolled finishes are used where a smoother surface is required.

Confirm the edge format, since mill edge and cut edge are not interchangeable for automatic welding lines.

For thicknesses above 25 mm, allow for a project lead time and agree the test and inspection documents at the order stage.

Where flatness is critical, request the special flatness class rather than the standard class, and state the maximum permitted deviation per metre.

Frequently Asked Questions

Q: What thickness range is available in 904L plate?
The normal mill range runs from 3.0 mm to 50.0 mm, with 3.0-6.0 mm readily available, 6.0-12.0 mm as standard plate, and 25.0-50.0 mm made to order.

Q: Which standards cover 904L plate?
ASTM B625 for UNS N08904, EN 10088-2 for EN 1.4539, and JIS G4304 for SUS 890L.

Q: Are 904L, 1.4539 and SUS 890L the same grade?
Yes. They are the American, European and Japanese designations of the same 904L chemistry, and they can be cross-referenced on the mill certificate.

Q: What tolerance applies to 3 mm 904L plate?
About ±0.3 to ±0.4 mm under ASTM, ±0.4 mm under EN and ±0.4 mm under JIS.

Q: Can 904L plate be supplied cut to size?
Yes. Plate is normally cut by waterjet or plasma to customer lengths, and mill edge or cut edge formats are both available.

Q: Why is flatness specified separately from thickness?
Thickness tolerance controls mass and strength, while flatness controls fit-up and welding. Flatness is agreed as a deviation per metre, typically 10 mm/m or 5 mm/m.

Send Inquiry