SUS310S Stainless Steel: High-Temperature Oxidation Resistance
Jan 16, 2026
Leave a message
Are you sourcing stainless steel for industrial furnaces, heat-treatment equipment, radiant tubes or high-temperature process piping? If conventional 304 or 316L stainless steel cannot provide the required oxidation resistance, SUS310S stainless steel is a heat-resistant austenitic grade worth evaluating for prolonged exposure to elevated temperatures.
What is SUS310S stainless steel?
SUS310S is a low-carbon chromium-nickel stainless steel, typically containing 24%–26% chromium and 19%–22% nickel. Its high chromium content allows for the formation of a protective chromium oxide film on the surface, which effectively inhibits further oxidation when the material is exposed to high-temperature, oxygen-containing environments. It is generally used in continuous operating environments at temperatures around 1050°C (1922°F), with a maximum service temperature reaching approximately 1100°C (2012°F).
What is the equivalent of SUS310S ?
• USA / ASTM / AISI: 310S (UNS S31008)
• Europe / EN / DIN: X8CrNi25-21 (EN 1.4845)
• China (GB): 0Cr25Ni20 or 06Cr25Ni20
• (GOST): 20Х23Н18 (or 10KH23N18)
What is the difference between 310S and 310H?
The key difference is carbon content: 310S has C ≤ 0.08% (low carbon, excellent weldability), while 310H has C 0.04–0.10% (higher carbon, precipitation hardening at 800–1,000 °C). 310H provides 15–25% higher creep strength above 800 °C due to Cr₂₃C₆ precipitation at grain boundaries. Use 310H for ASME pressure parts in creep-critical service; use 310S for welded structures.
SUS310S stainless steel Chemical Composition
| Element | SUS310S (JIS G4304) | UNS S31008 | EN 1.4845 |
| C | ≤ 0.08 | ≤ 0.08 | ≤ 0.08 |
| Si | ≤ 1.50 | ≤ 1.50 | ≤ 1.50 |
| Mn | ≤ 2.00 | ≤ 2.00 | ≤ 2.00 |
| P | ≤ 0.045 | ≤ 0.045 | ≤ 0.045 |
| S | ≤ 0.030 | ≤ 0.030 | ≤ 0.030 |
| Cr | 24.0 – 26.0 | 24.0 – 26.0 | 24.0 – 26.0 |
| Ni | 19.0 – 22.0 | 19.0 – 22.0 | 19.0 – 22.0 |
| N | ≤ 0.10 | ≤ 0.10 | ≤ 0.10 |
| Fe | Balance | Balance | Balance |
SUS310S stainless steel Mechanical Properties (Room Temperature, Annealed)
| Property | SUS310S (JIS) | SUS310S (ASTM A240) | Test Standard |
| Tensile Strength (min) | ≥ 520 MPa (75 ksi) | ≥ 515 MPa (75 ksi) | ASTM E8 |
| Yield Strength, 0.2% (min) | ≥ 205 MPa (30 ksi) | ≥ 205 MPa (30 ksi) | ASTM E8 |
| Elongation in 50 mm (min) | ≥ 40% | ≥ 30% | ASTM E8 |
| Hardness (max) | 217 HBW / 95 HRB | 217 HBW / 95 HRB | ASTM E10 / E18 |
SUS310S stainless steel High-Temperature Tensile Properties
| Temperature | 310S Tensile (MPa) | 310S Yield (MPa) | 310S Elongation (%) | 309S Tensile (MPa) | 304 Tensile (MPa) |
| 25 °C (77 °F) | 620 | 280 | 55 | 580 | 580 |
| 500 °C (932 °F) | 480 | 180 | 50 | 450 | 500 |
| 800 °C (1,472 °F) | 250 | 130 | 48 | 220 | 200 |
| 1,000 °C (1,832 °F) | 130 | 90 | 45 | 100 | 80 |
| 1,100 °C (2,012 °F) | 80 | 60 | 42 | 55 | 40 |
| 1,150 °C (2,100 °F) | 55 | 45 | 40 | 35 | 25 |
| 1,200 °C (2,192 °F) | 30 | 25 | 38 | 18 | 12 |
What is the maximum service temperature for SUS310S?
In dry air, the maximum service temperature for SUS310S is 1,150 °C (2,100 °F) for continuous use, and 1,035 °C (1,895 °F) for intermittent use. According to ASME standards, for structural (load-bearing) applications, the maximum service temperature is limited to 816 °C (1,500 °F) due to creep considerations; for furnace components that do not bear loads, the oxidation-resistance limit of 1,150 °C applies.
SUS310S vs. SUS309S:Maximum Service Temperature Limits
| Condition | SUS310S | SUS309S | SUS304 | SUS316L |
| Continuous service in dry air | 1,150 °C (2,100 °F) | 1,000 °C (1,830 °F) | 870 °C (1,598 °F) | 870 °C (1,598 °F) |
| Intermittent / cyclic service in air | 1,035 °C (1,895 °F) | 980 °C (1,796 °F) | 925 °C (1,700 °F) | 925 °C (1,700 °F) |
| Oxidizing (sulfur ≤ 2 g/m³) | 1,050 °C (1,922 °F) | 1,000 °C (1,832 °F) | 870 °C (1,598 °F) | 870 °C (1,598 °F) |
| Oxidizing (sulfur > 2 g/m³) | 950 °C (1,742 °F) | 900 °C (1,652 °F) | 815 °C (1,500 °F) | 815 °C (1,500 °F) |
| ASME B31.3 (pressure vessel) | 816 °C (1,500 °F) | 760 °C (1,400 °F) | 425 °C (800 °F) | 425 °C (800 °F) |
| Creep-critical (structural load) | ≤ 980 °C (1,796 °F) | ≤ 900 °C (1,652 °F) | ≤ 425 °C (800 °F) | ≤ 425 °C (800 °F) |
SUS310S vs. SUS309S:Thermal Cycling & Scale Life
| Parameter | 310S | 309S | 304 |
| CTE (0 – 1,000 °C) | 19.5 × 10⁻⁶ /°C | 19.0 × 10⁻⁶ /°C | 19.0 × 10⁻⁶ /°C |
| Scale CTE (Cr₂O₃) | ~10 × 10⁻⁶ /°C | ~10 × 10⁻⁶ /°C | ~10 × 10⁻⁶ /°C |
| CTE mismatch (metal − scale) | ~9.5 × 10⁻⁶ | ~9.0 × 10⁻⁶ | ~9.0 × 10⁻⁶ |
| Thermal shock resistance (1,000 → RT) | Excellent | Good | Poor |
| Scale adhesion (1,100 °C, 100 cycles) | > 95% intact | ~80% intact | ~40% intact |
| Recommended max cycle rate | 1 cycle/hr | 1 cycle/hr | 1 cycle/4hr |
Can 310S be used in sulfur-bearing atmospheres?
Yes, but with limits. 310S resists oxidation in sulfur-bearing atmospheres up to 950 °C (sulfur ≤ 2 g/m³) or 850 °C (sulfur > 2 g/m³). Above these limits, sulfidation (FeS, NiS formation) accelerates and the protective Cr₂O₃ scale is compromised. For high-sulfur service, consider Alloy 800H or C-276.
What is the creep strength of 310S at 1,000 °C?
At 1,000 °C, 310S has a creep rupture stress of approximately 9 MPa (1.3 ksi) at 10⁵ hours and a 0.2% proof stress of 5 MPa (0.7 ksi). This is sufficient for non-critical structural applications but inadequate for high-pressure vessels. For creep-critical service above 900 °C, use 310H or Inconel 600.
Can 310S be welded?
Yes. 310S is excellent for welding (low C ≤ 0.08%). Use ER310S / 310S filler metal (or 309S for dissimilar joints). No preheat or post-weld heat treatment is required. The weld HAZ is resistant to intergranular corrosion due to low carbon.
SUS310S Stainless Steel Supplier
GNEE offers SUS310S (UNS S31008) heat-resistant stainless steel in the form of plates, coils, strips, and pipes. Specific specifications and supply formats are subject to current inventory and production capacity. We provide a Material Test Certificate (MTC) covering chemical composition, mechanical properties, and heat number traceability. Upon request, we can also arrange for dimensional inspection, Positive Material Identification (PMI), and third-party testing.




When placing an order, please specify the product form, thickness (or pipe diameter), quantity, surface finish, operating temperature, and working conditions so that we can confirm the specifications, lead time, and pricing.
Send Inquiry






